- How can you tell the difference between an EMD and a GE locomotive?
- Do train drivers sleep?
- How many miles does a locomotive last?
- How many miles per gallon does a train get?
- What is a train sexually speaking?
- How much does a train locomotive cost?
- How are locomotives numbered?
- What is the most powerful locomotive ever built?
- How big is a train fuel tank?
- What is the difference between a train and a locomotive?
- Why do train engines not turn off?
- How much fuel do trains use to start?
- How much fuel does a train use per hour?
- Why would a train need more than one locomotive?
- What is the newest locomotive?
- Does GE still make locomotives?
- How do I identify a train engine?
- What EMD means?
How can you tell the difference between an EMD and a GE locomotive?
GE radiators are like a flat slab plopped on the back end of the locomotive, and overhanging the sides of the carbody.
EMD locomotives have flat sides, or on later models, flares.
Some GE’s have small flared sections below the slab, but they don’t extend out to the edges of the slab..
Do train drivers sleep?
The engineers and conductors get off the train, go to a hotel, rest until the next train comes and run it back to their origin point. … They do sleep on the train either in their own sleeping car, in the case of the sleeper attendants, or in the dorm car, in the case of the diner/snack crew.
How many miles does a locomotive last?
If you are talking locomotives, a few millions give or take rebuilds. If you are talking about specific train consists, sometimes a few miles sometimes a few thousand (in the USA, the Trans-Siberia Railroad might have consists that can last semi-close to 10,000 miles).
How many miles per gallon does a train get?
470 milesThanks in part to these technologies, today U.S. freight railroads can, on average, move one ton of freight more than 470 miles per gallon of fuel, making rail an environmentally friendly way to move freight over land.
What is a train sexually speaking?
To run train (or run a train) refers to when multiple men have sex with a woman one after the other, with or without consent.
How much does a train locomotive cost?
So, How much do locomotives cost? A diesel locomotive could cost from $500,000-$2 million. While an electric locomotive could cost more than $6 million. Price depends on whether it is powered by AC or DC traction, how much horsepower it has, or what electronics it is equipped with.
How are locomotives numbered?
Locomotives, steam or diesel, are numbered in classes, as example, Santa Fe F units were in 100, 200, 300, etc. classes. GP’s were not numbered in the same classes, they had their own.
What is the most powerful locomotive ever built?
Union Pacific CentennialThe Union Pacific Centennial is the largest and most powerful diesel locomotive ever built.
How big is a train fuel tank?
The fuel tank is normally under the loco frame and will have a capacity of say 1,000 imperial gallons (UK Class 59, 3,000 hp) or 5,000 US gallons in a General Electric AC4400CW 4,400 hp locomotive.
What is the difference between a train and a locomotive?
is that train is elongated portion or train can be (obsolete) treachery; deceit while locomotive is (rail transport) the power unit of a train which does not carry passengers or freight itself, but pulls the coaches or rail cars or wagons.
Why do train engines not turn off?
Another reason for not turning off diesel train engines, lies in the engine itself. … It is also interesting to know that while diesel locomotives are idling, fuel consumption is more than when the train is moving. This is because, while idling, the batteries are being charged, and the air compression is in operation.
How much fuel do trains use to start?
Similarly, a typical train might haul 3,000 tons of freight 500 miles and consume approximately 3,049 gallons of diesel fuel.
How much fuel does a train use per hour?
As the table in Figure 5 demonstrates, fuel consumption for conventional locomotives can vary from a low of around 3 gallon per hour (gph) while idling, up to a high range of 188 gph while at maximum notch. The most common switch engines for use in intermodal yards would be similar to the GP 9 or GP 38 locomotives.
Why would a train need more than one locomotive?
Double heading is practised for a number of reasons: The most common reason is the need for additional motive power when a single locomotive is unable to haul the train due to uphill grades, excessive train weight, or a combination of the two.
What is the newest locomotive?
The AC6000CW is a 6,000-horsepower (4,500 kW) road switcher diesel electric locomotive built by GE Transportation. It is among the world’s most powerful single-engined diesel locomotives.
Does GE still make locomotives?
The G.E. unit is a leading manufacturer of locomotives for freight trains, and it had sales of $4.2 billion in 2017. The combined company, Wabtec and G.E. executives said, will be stronger, have a broader mix of rail operations and become a Fortune 500 corporation.
How do I identify a train engine?
The suffix behind the number has the following meaning: AC = AC traction, M = Safety Cab, T = Tunnel motor. GE: “B” indicates a 4 axle locomotive, “C” indicates a 6 axle locomotive. The number is the number of horsepower divided by 100 (so 44 is a 4400 horsepower locomotive).
What EMD means?
Earnest Money DepositEMD stands for Earnest Money Deposit. And to break it down even further, the earnest money deposit is just a fancy name for the security deposit that the buyer puts down at the beginning of a real estate deal.